An HQ to WB Holden or a VB to VP Commodore takes two tapered roller bearings in each front hub: LM67048 (31.75 mm bore) in an LM67010 cup, and LM11949 (19.05 mm bore) in an LM11910 cup. Our 2x HQ to WB and VB to VP front wheel bearing kits include both, plus seals.
If the numbers on your old cones and cups match these, that's your kit. The sizes are below.
| Part | Number | Size |
|---|---|---|
| Larger cone | LM67048 | 31.75 mm (1 1/4") bore |
| Its cup | LM67010 | 59.13 mm outside diameter |
| Smaller cone | LM11949 | 19.05 mm (3/4") bore |
| Its cup | LM11910 | 45.24 mm outside diameter |
| Seal | One per wheel | Size not given in our car kit listings |
Source: bearing numbers and contents from our product listings, read 10 October 2026; bore and outside diameters are bearing makers' published part data (see Sources). Our listings write the larger pair in short form, LM67048/10: the LM67048 cone with its LM67010 cup.
Holden wheel bearing kits by model: HQ to WB and VB to VP
In our listings, every HQ to WB and VB to VP on the fit list takes the same front set. Our four kits for them all carry the same two bearings: ACCOR or KOYO, one wheel or both.
| Holden (as listed) | Years (as listed) | Engines (as listed) | Front kit |
|---|---|---|---|
| HQ | 1971 to 1974 | 6 and 8 cylinder | Any of our four HQ to VP kits |
| HJ | 1974 to 1976 | 6 and 8 cylinder | Same |
| HX | 1976 to 1977 | 6 and 8 cylinder | Same |
| HZ | 1977 to 1980 | 6 and 8 cylinder | Same |
| WB | 1980 to 1985 | 6 and 8 cylinder | Same |
| Commodore VB | 1978 to 1980 | 6 and 8 cylinder | Same |
| Commodore VC | 1980 to 1981 | 4, 6 and 8 cylinder | Same |
| Commodore VH | 1981 to 1983 | 4, 6 and 8 cylinder | Same |
| Commodore VK | 1984 to 1987 | 4, 6 and 8 cylinder | Same |
| Commodore VL | 1987 to 1990 | 4, 6 and 8 cylinder | Same |
| Commodore VN | 1990 to 1991 | 6 and 8 cylinder | Same |
| Commodore VP | 1991 to 1993 | 6 and 8 cylinder | Same |
| Holden 1 tonne, Toyota Lexcen VN and VP | Not stated | Not stated | KOYO front kit, one wheel |
| Torana LC 1971 to 1972, LH 1974 to 1976, LX 1975 to 1979, UC 1978 to 1979 | As shown | Not stated | KOYO front kit, one wheel |
Source: our listings' "Fits" lists, read 10 October 2026. The KOYO single kit lists the same series without years, and it's the only one naming the 1 tonne, Lexcen and Torana. Its Torana LJ line has no usable years, so for an LJ, send us your VIN.
None of our listings names a front wheel bearing for the VR Commodore or later.
Holden trailer kits use the same bearings
A Holden trailer bearing kit carries the same numbers: LM67048 in an LM67010 cup and LM11949 in an LM11910 cup. That shared pair is the HQ to WB and VB to VP Holden front wheel bearing set in our listings. A Ford (slimline) trailer set uses a different pair, L68149 and LM12749. How to tell the two apart on a trailer is in Holden or Ford trailer bearings? How to tell.
The seal is another matter. Our standard Holden trailer kits list theirs at 38.1 mm inside and 59.13 mm outside; our car kits give no seal size. So buy the car kit for the car and the trailer kit for the trailer.
Two checks before you order
- Read the old bearings. The numbers are stamped on each cone and cup. LM67048 with LM67010, and LM11949 with LM11910, is this set.
- Find your series and years in the table. Not there, or not sure? Send us your VIN or registration and we'll confirm it from the make, model, year and engine.
Fitting: Holden's workshop manual and a mechanic
Fitting and setting up front wheel bearings follows Holden's procedure for your model in the workshop manual. We don't publish fitting steps or torque figures. Without the manual and the tools, book a mechanic. Our listings say all parts should be fitted by a professional to vehicle specifications, and we agree.
Which Bearings Express kit fits
- Pick the 2x HQ to WB and VB to VP front kits for both front wheels (ACCOR), or the single kit for one.
- Pick the 2x KOYO HQ to WB and VB to VP front kits for both front wheels with KOYO bearings, made in Japan.
- Pick the KOYO front kit for HQ to WB, VB to VP or Torana for one wheel, or for the Torana, 1 tonne or Lexcen on its list.
- Pick the 2x standard trailer bearing kits for Holden axles if it's the trailer, not the car.
The bearing numbers decide the fit; the brand is your choice. ACCOR is our economy brand, from a high-end Chinese maker whose bearings were used in military vehicles and as Holden original equipment on late Commodores. KOYO is a good-quality Japanese maker.
Other Holdens in our wheel bearing listings
These use different bearings. Check your engine and years on each listing's fit list.
| Holden (as listed) | Front or rear | Our kit (one wheel) |
|---|---|---|
| Barina TK 1.6 (2005 to 2012) | Front | Front kit for Daewoo, Holden Barina and Golf or the GMB front kit for Holden Barina |
| Barina TK 1.6 (2005 to 2012), Barina Spark MJ 1.2 (2010 to 2015) | Rear | Rear kit for Holden Barina and others |
| Apollo JM (1993 to 1995), JP (1995 to 1997) | Front | Front kit for Holden Apollo and Toyota Camry |
| Cruze YG 1.5 hatch (2002 to 2006) | Rear | Rear kit for Holden Cruze and others; its listing says there's more than one possibility, so send us your VIN |
| Rodeo KB and TF (1985 to 2003) | Rear | Rodeo rear kit |
| Jackaroo (1992 to 2004), Frontera (1999 to 2004), Monterey (2000 to 2003) | Front | Front kit for Colorado, Jackaroo, Rodeo and D-Max |
Source: our listings' "Fits" lists, read 10 October 2026. Colorado and Rodeo RA and TF fronts are in Colorado and D-Max front wheel bearings. Pairs and everything else are in wheel bearing kits and hub units.
Questions people also ask
Do you have front wheel bearings for a VR to VZ Commodore?
Not in our current listings. Our Commodore front kits stop at the VP, so send us your VIN for a VR or later.
Do you have rear wheel bearings for an HQ or a Commodore?
None of our listings names an HQ to WB rear. Commodore rears are separate kits, listed by series and rear suspension, in wheel bearing kits and hub units.
Related reading
- Holden or Ford trailer bearings? How to tell
- Identifying trailer hub types, stud patterns and PCD
- Holden Colorado and Isuzu D-Max front wheel bearings
Sources
- Timken, part pages for LM67048, LM11949 (bore) and LM67010, LM11910 (outside diameter), https://cad.timken.com/item/all-categories/tapered-roller-bearings-2/lm67048 (and the matching page for each part number), read 27 September 2026, rechecked 10 October 2026.
Checked against the bearing maker's part data above and Bearings Express product listings on 10 October 2026.
0 comments